My Setup
Hey hows everyone today? I have a few questions concerning my car audio equipment. I'm still fairly new at this, so anything would be greatly appreciated. I bought two 10" Pioneer Champion series sub woofers, a Kenwood 2-Channel Car Amplifier (KAC-7205), and an Alpine IDA-X303 head unit. I recently looked up the specifications for the amplifier and from what I do know this isn't the best amp for my subs. Can anyone please tell me if this is the proper amp I need or if i should invest in a new one. If it is the recommended amp does anyone have a tuning setup? Thank you very much in advance. Also I'm using 4guage wiring.
|
Are the subs dual 4ohm or dual 2 ohm models? Generally most people would recommend a mono block (one channel, frequency response limited) class d amp for the subs. However, depending on the voice coil configuration you have, that will determine what's the best amp to get as not all amps are stable to lower impedance. You'll want an amp that puts out 700-800 watts rms at the final impedance load created by your subwoofers to get maximum results.
|
Originally Posted by veeman
(Post 596547)
Are the subs dual 4ohm or dual 2 ohm models? Generally most people would recommend a mono block (one channel, frequency response limited) class d amp for the subs. However, depending on the voice coil configuration you have, that will determine what's the best amp to get as not all amps are stable to lower impedance. You'll want an amp that puts out 700-800 watts rms at the final impedance load created by your subwoofers to get maximum results.
heres the amp RATED OUTPUT POWER (14.4V): * 170W RMS x 2 @ 4 Ohms (20Hz-20kHz @ 0.08%THD) * 250W RMS x 2 @ 2 Ohms (1kHz @ 0.8% THD) * 500W RMS x 1 @ 4 Ohms (1kHz @ 0.8% THD) (Bridged) no clue what any of this means..... |
so, it'll play reasonably loud, but you're at about 2/3 the max rms that the subs can handle. a more appropriate amp (read that as; able to get your subs louder) would be a single channel mono block that delivers 700-800 watts @ 1ohm as your final load impedance is either 1, 4 or 16 ohms (at 4ohm would be just as good or better but they are much more expensive and not needed for subwoofers under daily use).
|
Originally Posted by veeman
(Post 596576)
so, it'll play reasonably loud, but you're at about 2/3 the max rms that the subs can handle. a more appropriate amp (read that as; able to get your subs louder) would be a single channel mono block that delivers 700-800 watts @ 1ohm as your final load impedance is either 1, 4 or 16 ohms (at 4ohm would be just as good or better but they are much more expensive and not needed for subwoofers under daily use).
|
Amps are like hookers, depends on your budget. Any decent brand name amp will do the job. If you find a good deal on a 1000 watt amp, as they tend to sell amps in 500 watt increments, that would be fine...the subs will rarely see full power for a prolonged time unless you're a teenager with no idea of what distortion sounds like.
|
Originally Posted by veeman
(Post 596612)
Amps are like hookers, depends on your budget. Any decent brand name amp will do the job. If you find a good deal on a 1000 watt amp, as they tend to sell amps in 500 watt increments, that would be fine...the subs will rarely see full power for a prolonged time unless you're a teenager with no idea of what distortion sounds like.
|
No problem...welcome to the board!
|
Originally Posted by veeman
(Post 596614)
No problem...welcome to the board!
|
Originally Posted by 01Forester
(Post 598477)
quick question. Since I'm only running 2/3rds the power can I tune the bass on the amp for max power? Or will I blow my speakers. Thanks in advance!
If you do tweak anything higher, keep a very close ear on your subs.....if you hear distortion back the volume off.....the subs will thank you by continuing to work until you get the bigger amp......:smokin: HTH |
All times are GMT -5. The time now is 01:41 PM. |
© 2024 MH Sub I, LLC dba Internet Brands