quick question. need to no asap
 

i got a sub. and i need to get an amp. just sum 1 who no's abbout subs and amps like hookin them up tell me if this would work right.

PIONEER 12" 800 WATT SUBWOOFER

* Cone material: injection-molded polypropylene (IMPP) composite for strength and durability
* Surround: urethane, dual layer
* Magnet type: strontium
* Voice coil: four-layer with aluminum bobbin
* Damper: Conex for linear bass response<
* Basket design: stamped with magnet cover
* Gasket: molded
* Terminals: spring compression
* Nominal power handling capability: 150 watts RMS
* Maximum music power handling capability: 800 watts
* Frequency response: 20 to 4000 Hz
* Sensitivity: 91 dB (1 watt at 1 meter)
* Impedance rating: 4 ohms
* Mounting depth: 5.75 inches
* Cut-out dimension: 10.9 inches
* Weight: 1.5 lbs.
* Recommended enclosure size: 1 to 2 cubic feet

SONY XPLOD 1000 WATT 2 CHANNEL AMPLIFIER

* MOSFET Power Supply
* Balanced Input Circuit
* Speaker Level Input
* 2-Channels
* 1000 Watts
* Gold Plated Connectors
* Graphite Gray

Top of Page
Specifications
General
Product Type: Amplifier
Recommended Use: Car
Width: 16.7 in
Depth: 11.4 in
Height: 2.2 in
Weight: 8.8 lbs
Series: Xplod
Miscellaneous
Included Accessories: Cable kit, mounting hardware
Connections
Connector Type: 1 x audio line-in ( RCA phono x 2 ) ¦ Speakers input ¦ Speakers output ( screw-type ) ¦ DC power input ( screw-type )
Audio System
Max Output Power / Channel Qty: 380 Watts x 2
Crossover: Active crossover
Additional Features: Input level controls
Response Bandwidth: 5 - 80000 Hz
Signal-To-Noise Ratio: 93 dBA
Continuous Power / Channel Qty: 165 Watts x 2
Amplifier Output: 2-channel
High Level Inputs: Yes
Input Signal Voltage: 0.3 - 6V, 1.2 - 12V
Crossover Slope: 18 dB/octave
Low Pass Frequencies: 80 Hz
Output Power / Total: 1000 Watt
Distortion Factor: 0.008%
Amplifier Output Details: 165 Watt - 4 Ohm - 20 - 20000 Hz - THD 0.04% - 14.4V DC - 2 channel(s) ¦ 200 Watt - 2 Ohm - 20 - 20000 Hz - THD 0.1% - 14.4V DC - 2 channel(s) ¦ 400 Watt - 4 Ohm - 20 - 20000 Hz - THD 0.1% - 14.4V DC - 1 channel(s)
More Information
Model No.: XM-1652Z
Shipping Weight (in pounds): 11.2
Assembled in Country of Origin: Imported
Origin of Components: Imported
Wal-Mart No.: 001087444

yah it will work at 4 ohm mono on the amp. will be too much power tho.

look for an amp that puts out around 200 watts mono or bridged.

so if i get a 200 watt 2 channel amp im good?

Yeah, around 100 watts per channel or a 200 watt single channel (monoblock) amp will be just fine.

I really don't see how that sony amp would be too much power. It's 400W @ 4ohms when bridged mono.

That sub will take 400 rms. I've used pioneer subs before.
Most of their speakers are underrated on the 'Nominal" power.

Most mfgs have rms at around half the max. Pioneer goes way low on the ratings, to protect themselves from warrantee issues.

As long as you stay out of clipping they'll work fine.