SoundStream 644S
#1
Does anyone know how much power a SoundStream 644S will put out with 2 channels bridged into 1ohm with 14.4volts (the other 2 channels running 4ohm stereo FYI)
I'm guessing around 400rms, but i'm hoping for more
I'm guessing around 400rms, but i'm hoping for more
#2
#5
I sold both of mine... <sniff>, but I go along with Jeepbeats.
As I recall unregulated power supplies so more volts fed makes more power.
I don't think I'd run that amp with that low an impedance myself (they did get the name smokesteam for a reason). They had a run of suspect power supplies as I understand it. Very sweet sounding amps though.
The Hammer
As I recall unregulated power supplies so more volts fed makes more power.
I don't think I'd run that amp with that low an impedance myself (they did get the name smokesteam for a reason). They had a run of suspect power supplies as I understand it. Very sweet sounding amps though.
The Hammer
#6
Thanx for the info guys.
I'll explain a little more, I'm looking for a single amp for my speakers up front and 4 RE8's with single 4ohm coils (4ohm x1, 1ohm x1, 2ohm x2, or 8ohm x2) I have a 6 channel amp but I don't think it will do 2ohm bridged, So I could run it 4ohm stereo on all channels, but I wouldn't be using the amp to its potential.
Any suggestions?
[ May 16, 2005, 11:24 PM: Message edited by: Phiber Optik ]
I'll explain a little more, I'm looking for a single amp for my speakers up front and 4 RE8's with single 4ohm coils (4ohm x1, 1ohm x1, 2ohm x2, or 8ohm x2) I have a 6 channel amp but I don't think it will do 2ohm bridged, So I could run it 4ohm stereo on all channels, but I wouldn't be using the amp to its potential.
Any suggestions?
[ May 16, 2005, 11:24 PM: Message edited by: Phiber Optik ]
#7
You already have the 644S?
Heck lots of folks have done it with success .. I'd suggest some sort of forced air cooling (fan).
Worst it's gonna do is flame up... lol
I ran across a guy that said he was able to verify by serial number which amps were from the 'bad batch'.
I'll see if I can find his contact info again.
Maybe you should do some bench testing with the amp and see for yourself how it likes 1ohm.
I have a Nak PA-2004(zed audio) I'm planning on running 2x100W (4ohm stereo)+ 1 x 400W (4ohm mono).
If your interested I have 2 more of these 4x100W amps NIB
Maybe you should grab a Zed Kronos when they come out. that would fix you up nice.
How much power do those RE8"s want?
The Hammer
[ May 17, 2005, 03:06 AM: Message edited by: TheHammer ]
Heck lots of folks have done it with success .. I'd suggest some sort of forced air cooling (fan).
Worst it's gonna do is flame up... lol
I ran across a guy that said he was able to verify by serial number which amps were from the 'bad batch'.
I'll see if I can find his contact info again.
Maybe you should do some bench testing with the amp and see for yourself how it likes 1ohm.
I have a Nak PA-2004(zed audio) I'm planning on running 2x100W (4ohm stereo)+ 1 x 400W (4ohm mono).
If your interested I have 2 more of these 4x100W amps NIB
Maybe you should grab a Zed Kronos when they come out. that would fix you up nice.
How much power do those RE8"s want?
The Hammer
[ May 17, 2005, 03:06 AM: Message edited by: TheHammer ]
Thread
Thread Starter
Forum
Replies
Last Post
PsychoAcoustics Canada
Canadian General Car Audio Discussion
142
11-24-2009 08:33 PM
King-Kong
General Discussion
10
09-11-2008 02:25 PM