A-Rok Productions Presents............
Thread Starter
50 Watt CAFz'r
Joined: May 2003
Posts: 356
50 Watt CAFz'r
Joined: Nov 2001
Posts: 306
Toss a bit of of fabris over it to get an idea of what it'll look like.
The secret to successful fibreglassing is to buy the ugliest fabric you can find.
This **** was bought from Walmart and was obviously some sort of fat woman's spandex material.
The ugliest material is by far the most effective. Plus it was in th ebargain bin for just $1.50 a meter. 2 birds with 1 stone batman.
The secret to successful fibreglassing is to buy the ugliest fabric you can find.
This **** was bought from Walmart and was obviously some sort of fat woman's spandex material.
The ugliest material is by far the most effective. Plus it was in th ebargain bin for just $1.50 a meter. 2 birds with 1 stone batman.
50 Watt CAFz'r
Joined: Nov 2001
Posts: 306
A little known secret to keeping your **** from getting wrecked is to lay a thin sheet of plexi on your tool box and use it as a bench.
Note how it fits good.
The key to getting it to fit good is to try and jam it in there with enough force that the plexy snaps on one side or another (the left side), then after actually using your brain, go and sand it down until it slides in with ease.
When you start to fibreglass your material, you should always ensure that you have the proper tools for the job, especially a sufficient mixing stick.
[ March 22, 2004, 01:16 AM: Message edited by: A-Rok ]
Note how it fits good.
The key to getting it to fit good is to try and jam it in there with enough force that the plexy snaps on one side or another (the left side), then after actually using your brain, go and sand it down until it slides in with ease.
When you start to fibreglass your material, you should always ensure that you have the proper tools for the job, especially a sufficient mixing stick.
[ March 22, 2004, 01:16 AM: Message edited by: A-Rok ]
50 Watt CAFz'r
Joined: Nov 2001
Posts: 306
This where I'm reayd to glass the up now.
The wind picked up and my nipples were hard enoug h to cut diamonds, so I closed the garage door to proceed onto the next part.
atfer g;sasin pu the box i flet A LITTLWE dissy.
tshis wasa a goot trime to bresak a take.
The wind picked up and my nipples were hard enoug h to cut diamonds, so I closed the garage door to proceed onto the next part.
atfer g;sasin pu the box i flet A LITTLWE dissy.
tshis wasa a goot trime to bresak a take.
50 Watt CAFz'r
Joined: Nov 2001
Posts: 306
Well, I guess that'll have to do for now little piggy.
I think, however, we should show a couple shots of the gorgeous as Denver sub going there.
Perhaps we'll have a few more shots later this week on the project progress. Actually, we'd better have a few more shots since we set a time limit on this little project of two weeks to make room for the more serious and important projects.
I think, however, we should show a couple shots of the gorgeous as Denver sub going there.
Perhaps we'll have a few more shots later this week on the project progress. Actually, we'd better have a few more shots since we set a time limit on this little project of two weeks to make room for the more serious and important projects.
Guest
Posts: n/a
I want to know why there is filler slathered all over the outside of the enclosure? Usually when I stretch something it is pretty smooth - just have to get rid of the resin ripple. [img]graemlins/dunno.gif[/img]
Not saying it is done wrong but that's a lot of extra work IMO
Not saying it is done wrong but that's a lot of extra work IMO
