alpine 3517?
#2
The 3527 does 25x4 at 4 ohms, maybe yours does 25x2?
http://www.stylestandard.net/oswego/Rooms/RoomComponents/AssetView/MoreInfo?Document=com.webridge.entity.Entity%5BOID %5BB87696852F0FD511B0A700508BB8123D%5D%5D&Containe r=com.webridg e.entity.Entity%5BOID%5B311BDA676903D511B0A000508B B8123D%5D%5D&component=
How is the 160x4 doing??
Ross
[ July 09, 2004, 11:51 PM: Message edited by: JeepBeats ]
http://www.stylestandard.net/oswego/Rooms/RoomComponents/AssetView/MoreInfo?Document=com.webridge.entity.Entity%5BOID %5BB87696852F0FD511B0A700508BB8123D%5D%5D&Containe r=com.webridg e.entity.Entity%5BOID%5B311BDA676903D511B0A000508B B8123D%5D%5D&component=
How is the 160x4 doing??
Ross
[ July 09, 2004, 11:51 PM: Message edited by: JeepBeats ]
#6
Hi guys,
I have an old 3517 myself and this is the info the manual holds. Hope it helps you out.
Alpine 3517
The Alpine 3517 is a high-power high-efficiency power amplifier, according to the Owner's Manual.
Features
30 Watts per channel
into 4 ohms, 20 - 20 KHz at 0.08%THD)
DC to DC Switching Mode Power Supply
4/2 Rated Speaker Impedance
Remote power on/off circuitry
(controlled by head unit)
High Current Capability
DIN and RCA Inputs
Input Gain Selector:
-DIN Jack - (Fixed) 500mV
-RCA Jack - (Variable) 100mV - 2V
Discrete Output Circuitry
Low RFI/EMI Emissions
Common Mode Detection Circuitry
Soft Start Circuitry
Torrodial Power Transformer
Power Supply Input and Output Filters
Remote-on Indicator and Circuitry
Isolated Signal Ground
Overheating Prevention Circuitry
Overvoltage, Miswiring, Speaker & Over Current Protections
Specifications
Power Output
-30W x 2 into 4 ohms from 20 Hz - 20 KHz at 0.04% THD
-35W x 2 into 2 ohms from 20 Hz - 20 KHz at 0.08% THD
Signal to Noise Ratio
-85 dBA at 1W output
-100 dBA at 30w output
Frequency Response
-10 Hz to 50 KHz (+0, -1 dB)
Input Sensitivity
-Variable: 18 mV - 364 mV (continuously variable) for 1W output into 4 ohms,
-100mV - 2V (continuously variable) for rated power output (30W x 2) into 4 ohms
Input Impedance 10K ohm
Speaker Impedance 4 or 2 ohms
Slew Factor greater than 5
Power Requirement
-14.4V DC negative ground, 11 - 16V allowable
Fuse Requirement 15A
Dimensions (WxHxD) 200 x 40 x 130mm
Weight 1.2 Kg
I have an old 3517 myself and this is the info the manual holds. Hope it helps you out.
Alpine 3517
The Alpine 3517 is a high-power high-efficiency power amplifier, according to the Owner's Manual.
Features
30 Watts per channel
into 4 ohms, 20 - 20 KHz at 0.08%THD)
DC to DC Switching Mode Power Supply
4/2 Rated Speaker Impedance
Remote power on/off circuitry
(controlled by head unit)
High Current Capability
DIN and RCA Inputs
Input Gain Selector:
-DIN Jack - (Fixed) 500mV
-RCA Jack - (Variable) 100mV - 2V
Discrete Output Circuitry
Low RFI/EMI Emissions
Common Mode Detection Circuitry
Soft Start Circuitry
Torrodial Power Transformer
Power Supply Input and Output Filters
Remote-on Indicator and Circuitry
Isolated Signal Ground
Overheating Prevention Circuitry
Overvoltage, Miswiring, Speaker & Over Current Protections
Specifications
Power Output
-30W x 2 into 4 ohms from 20 Hz - 20 KHz at 0.04% THD
-35W x 2 into 2 ohms from 20 Hz - 20 KHz at 0.08% THD
Signal to Noise Ratio
-85 dBA at 1W output
-100 dBA at 30w output
Frequency Response
-10 Hz to 50 KHz (+0, -1 dB)
Input Sensitivity
-Variable: 18 mV - 364 mV (continuously variable) for 1W output into 4 ohms,
-100mV - 2V (continuously variable) for rated power output (30W x 2) into 4 ohms
Input Impedance 10K ohm
Speaker Impedance 4 or 2 ohms
Slew Factor greater than 5
Power Requirement
-14.4V DC negative ground, 11 - 16V allowable
Fuse Requirement 15A
Dimensions (WxHxD) 200 x 40 x 130mm
Weight 1.2 Kg
#7
Regarding these amps. My 3519 harness is missing the Ignition cable..judging from the din input, im guessing the ignition is for the din only, so if i were not to hook up the ignition, the amp would work fine?
[img]graemlins/dunno.gif[/img]
[img]graemlins/dunno.gif[/img]
Thread
Thread Starter
Forum
Replies
Last Post
inquire4f4
Car Audio Technical Discussions
0
08-04-2014 05:15 AM