MTX Mono Amps
02-08-2008, 05:03 PM
#5
50 Watt CAFz'r
Thread Starter
Join Date: Oct 2007
Posts: 141
as a matter of fact, i called MTX this afternoon.
i asked if this pair would be a good match and the sales rep said not really.
he said that the MZS 1004 is a single voice coil sub and that the X Thunder 300D is better suited for a dual voice coil.
he said that for the MZS 1004, the best matches would be the TC 3002 or the TC 2002.
Do you agreee?
Jazz
02-11-2008, 07:34 PM
#6
50 Watt CAFz'r
Thread Starter
Join Date: Oct 2007
Posts: 141
I checked the amps that the rep at MTX recommended to me for the MZS 1004. Its wierd but they are 2 channel amps. Why would he recommend a 2 channel amp for a single 10" Sub?
I also downloaded the manual for the MZS 1004. In the specifications, it says 150 - 300 Watt RMS.
In a case like this, what wattage should the amp be RMS.
Thanks for any help on this
Jazz
I also downloaded the manual for the MZS 1004. In the specifications, it says 150 - 300 Watt RMS.
In a case like this, what wattage should the amp be RMS.
Thanks for any help on this
Jazz
02-11-2008, 07:38 PM
#7
it may be a two channel amp but he likely plans on you bridging it, with mono amps to get them really working you need really low impedence most two channel amps make there max power bridged at 4ohm. most people here are likely runnng amps that make alot more power then the subs are rated for, but wither way try to atleast stay to the high end of the power range.
My single 12 is rated for 600RMS and its getting around 700RMS
My single 12 is rated for 600RMS and its getting around 700RMS
02-11-2008, 09:30 PM
#8
50 Watt CAFz'r
Thread Starter
Join Date: Oct 2007
Posts: 141
it may be a two channel amp but he likely plans on you bridging it, with mono amps to get them really working you need really low impedence most two channel amps make there max power bridged at 4ohm. most people here are likely runnng amps that make alot more power then the subs are rated for, but wither way try to atleast stay to the high end of the power range.
My single 12 is rated for 600RMS and its getting around 700RMS
My single 12 is rated for 600RMS and its getting around 700RMS
http://www.mtx.com/caraudio/products...ta_MZS1004.pdf
It does not even state what the peak is!
Should i be looking for a Mono amp that puts out 300W RMS for best results?
Thanks
Jazz
02-11-2008, 09:43 PM
#9
it doesnt state peak because peak is kind of a mythical creature, RMS is the amount the amp can continuously deliver and the amount the sub can continuously handle 
the minimum number is the minimum recommended, under powering is often worse then over powering...
If you plan on staying with this sub forever then yeah something that maxes out a 300RMS will be fine, what you will notice when looking at single channel amps is that they have ratings for 4ohm 2ohm 1ohm and when you get into the real high end stuff they have .5ohm and .25ohm ratings. If you plan to run one of these subs then look for something that makes around 300RMS at 4ohm, and if you are buying a mono amp you'll be much better off in the long run when it comes to adding more/bigger subs, because as you increase the amount of drivers or switch to different voice coils you' ll beable to wire to get more power out of the amp, alot of 300RMS at 4ohm are often also rated around 600RMS at 2ohm, etc etc. this way you can stay with the amp as your system grows and your demands increase. Instead of having to buy a new amp every time you want to change up the subs
the minimum number is the minimum recommended, under powering is often worse then over powering... If you plan on staying with this sub forever then yeah something that maxes out a 300RMS will be fine, what you will notice when looking at single channel amps is that they have ratings for 4ohm 2ohm 1ohm and when you get into the real high end stuff they have .5ohm and .25ohm ratings. If you plan to run one of these subs then look for something that makes around 300RMS at 4ohm, and if you are buying a mono amp you'll be much better off in the long run when it comes to adding more/bigger subs, because as you increase the amount of drivers or switch to different voice coils you' ll beable to wire to get more power out of the amp, alot of 300RMS at 4ohm are often also rated around 600RMS at 2ohm, etc etc. this way you can stay with the amp as your system grows and your demands increase. Instead of having to buy a new amp every time you want to change up the subs
02-12-2008, 05:38 AM
#10
50 Watt CAFz'r
Thread Starter
Join Date: Oct 2007
Posts: 141
it doesnt state peak because peak is kind of a mythical creature, RMS is the amount the amp can continuously deliver and the amount the sub can continuously handle the minimum number is the minimum recommended, under powering is often worse then over powering...
If you plan on staying with this sub forever then yeah something that maxes out a 300RMS will be fine, what you will notice when looking at single channel amps is that they have ratings for 4ohm 2ohm 1ohm and when you get into the real high end stuff they have .5ohm and .25ohm ratings. If you plan to run one of these subs then look for something that makes around 300RMS at 4ohm, and if you are buying a mono amp you'll be much better off in the long run when it comes to adding more/bigger subs, because as you increase the amount of drivers or switch to different voice coils you' ll beable to wire to get more power out of the amp, alot of 300RMS at 4ohm are often also rated around 600RMS at 2ohm, etc etc. this way you can stay with the amp as your system grows and your demands increase. Instead of having to buy a new amp every time you want to change up the subs
the minimum number is the minimum recommended, under powering is often worse then over powering... If you plan on staying with this sub forever then yeah something that maxes out a 300RMS will be fine, what you will notice when looking at single channel amps is that they have ratings for 4ohm 2ohm 1ohm and when you get into the real high end stuff they have .5ohm and .25ohm ratings. If you plan to run one of these subs then look for something that makes around 300RMS at 4ohm, and if you are buying a mono amp you'll be much better off in the long run when it comes to adding more/bigger subs, because as you increase the amount of drivers or switch to different voice coils you' ll beable to wire to get more power out of the amp, alot of 300RMS at 4ohm are often also rated around 600RMS at 2ohm, etc etc. this way you can stay with the amp as your system grows and your demands increase. Instead of having to buy a new amp every time you want to change up the subs
Great response, very informative, thank you.
The sub that i am looking at is a single voice coil. How does this come into play when looking for an amp? I dont really know how its different from a dual voice coil.
Thanks
Jazz
