would this work?
07-12-2003, 08:08 AM
#1
0 Watt CAFz'r
Thread Starter
Join Date: Jun 2003
Posts: 17
would this work for 2 RE8's ?
- 27" x 14" x 12" @ 1.94 cu.ft. Gross Vol. / 1.22 cu.ft. Net Vol. - Common Chamber, Slot Port @ Fb 34 Hz - 2" x 12 1/2" x 42 5/8" I.D. sorry for being a pest
- 27" x 14" x 12" @ 1.94 cu.ft. Gross Vol. / 1.22 cu.ft. Net Vol. - Common Chamber, Slot Port @ Fb 34 Hz - 2" x 12 1/2" x 42 5/8" I.D. sorry for being a pest
07-12-2003, 08:12 AM
#2
Guest
Posts: n/a
IMO your port is too big - you only need 12-15sq in of area IMO for it to work just fine and this will make for a way shorter port (hint: vents over 2feet long are bad)
I'd keep the gross volume at 2cuft or so though - all else looks good.
I'd keep the gross volume at 2cuft or so though - all else looks good.
07-12-2003, 08:34 AM
#3
0 Watt CAFz'r
Thread Starter
Join Date: Jun 2003
Posts: 17
Thanks very much.....wish I knew what I was doing...so my vent should only go about the depth of the box?
07-12-2003, 09:02 AM
#4
50 Watt CAFz'r
Join Date: Dec 2001
Posts: 197
Sorry, dont mean to hijack the thread, but im curious about what dukk said about vents over 2 feet long are bad. Just wondering if that rule applies to the more powerful speakers as well? (An L7 in a big ported box for example)
07-12-2003, 02:57 PM
#5
0 Watt CAFz'r
Thread Starter
Join Date: Jun 2003
Posts: 17
I don't mind the thread being hijacked at all.
I just want to build a box...might have to pay someone for blueprints though. [img]smile.gif[/img]
I just want to build a box...might have to pay someone for blueprints though. [img]smile.gif[/img]
07-12-2003, 03:05 PM
#6
http://www.carstereo.com/help/Articles.cfm?id=31
this is a very helpful link,as for the port length calculation,swap the hight and length and use the longer port of the two.this one works good!!! [img]graemlins/thumb.gif[/img]
this is a very helpful link,as for the port length calculation,swap the hight and length and use the longer port of the two.this one works good!!! [img]graemlins/thumb.gif[/img]
07-12-2003, 03:36 PM
#7
0 Watt CAFz'r
Thread Starter
Join Date: Jun 2003
Posts: 17
Tried the calculator and still says I need a vent 42 in. ACK my head hurts.
07-12-2003, 06:39 PM
#8
50 Watt CAFz'r
Join Date: Dec 2001
Posts: 197
Relax dude. just reread what dukk said. Try making your port 2" x 6" and you'll get a more reasonable length.
The bigger the port area (2" x 6" = 12 square inches, that's the port area) the longer the port has to be.
The bigger the port area (2" x 6" = 12 square inches, that's the port area) the longer the port has to be.
07-12-2003, 07:04 PM
#9
0 Watt CAFz'r
Thread Starter
Join Date: Jun 2003
Posts: 17
ok so 27"x14"x12" vent 2"x6" 11" deep sound about right?......or round 3.25x 8.66 deep if I went with just a round port.....this will be my last post...promise [img]graemlins/@bow.gif[/img]
07-13-2003, 08:58 AM
#10
Guest
Posts: n/a
^ That should work fine but consider a 4"diameter port.
If your vents wind up over 2 feet long then the box probably has the condition of being too small or tuned too low or too much port area. People will go on and on about 'pipe resonances' and blah blah blah but usually if you see a mega long vent in a design there's a problem - not always, but usually.
If your vents wind up over 2 feet long then the box probably has the condition of being too small or tuned too low or too much port area. People will go on and on about 'pipe resonances' and blah blah blah but usually if you see a mega long vent in a design there's a problem - not always, but usually.
