Turning down the volume on tweeters
I've got a set of infinity 6020cs components running off an enegy crossover(the infinity one only goes to -3Db energy goes to-6Db) The amp is alpine mrp f300. I've also turned down the treble at the deck but the tweeters are still to loud for me. I've done some research into using and L-pad but it seems a little much for what I want. Can't I just use a resistor after the crossover, and if i can where would I get one that can stand up to 50watts rms.
|
You were on the right track. An L pad will do the trick for you. Resistors can be had at most electronic shops. You can also order them from solen and parts connexion.
|
your main issue is that you have the infinity speakers lol.. they are loud and not to my liking either. ( too harsh ) but maybe you will make them work good and sound good. good luck
|
I have to agree ,I have the infinity components as well and find they really get in my face. I have the x-overs set at -3db but they are still way to bright. Turning the treble on the source way down helps but.... They may end up for sale at some point.
|
I'm not sure what you are running equipment-wise, but I would honestly just try EQ'ing them to get them to sound more acceptable. It's amazing what an EQ can do.
|
Another thought, are you concerned about the shrillness of the tweeters or is the volume of the tweeter itself too high?
If it's the volume, you might consider making sure your doors are deadened to heighten your midbass and if you are running a sub, turn the volume up to blend with your fronts. Sorry, I'm too lazy to go back and check your sig. |
Another angle to look at it is perhaps that you're using crossovers from a different set, and xover points are not liked by your speakers. It could be either the tweets are not liking to be playing so low and getting into fs resonance issues, or the mids dont like playing to high and getting into cone break-up. Either one will sound very harsh, and it gets worse with more volume. Just a thought.
|
only a few options for you, 1 and 4 are cheapest;
1- Best- L-Pad ( lowers tweeter volume without shifting crossover point) 2- alter xover point if it is midrange edge (this works pretty good if the problem is the upper end of the mid driver or the lower end of the tweet) 3- add another product that can also EQ the system (this will add system noise) 4- in line resistors (they cause xover point issues) 5- get a different tweeter... 6- move the tweeters or at least change their angle |
Originally Posted by danyman
(Post 486520)
your main issue is that you have the infinity speakers lol.. they are loud and not to my liking either. ( too harsh ) but maybe you will make them work good and sound good. good luck
Originally Posted by Sasha
(Post 486539)
Another angle to look at it is perhaps that you're using crossovers from a different set, and xover points are not liked by your speakers. It could be either the tweets are not liking to be playing so low and getting into fs resonance issues, or the mids dont like playing to high and getting into cone break-up. Either one will sound very harsh, and it gets worse with more volume. Just a thought.
Originally Posted by JohnVroom
(Post 486642)
only a few options for you, 1 and 4 are cheapest;
1- Best- L-Pad ( lowers tweeter volume without shifting crossover point) 2- alter xover point if it is midrange edge (this works pretty good if the problem is the upper end of the mid driver or the lower end of the tweet) 3- add another product that can also EQ the system (this will add system noise) 4- in line resistors (they cause xover point issues) 5- get a different tweeter... 6- move the tweeters or at least change their angle |
Weber L-Pad Design <- clickie
nice crossover site <- clickie passive design <- clickie I just did my first home made passive design not as cheep as you might think but satisfying I have some variable L-pads from my SHO and they are still a valued asset |
All times are GMT -5. The time now is 11:44 PM. |
© 2024 MH Sub I, LLC dba Internet Brands