can someone tell me how to install subs
11-17-2003, 12:36 AM
#3
0 Watt CAFz'r
Thread Starter
Join Date: Nov 2003
Posts: 2
k then, how do u like connect it up, like for example, u put the subs in the back then where to u connect the wires up to.
also if u no a site that tells u in detail could u plz tell me or if u no how to anyways then plz tell me
also if u no a site that tells u in detail could u plz tell me or if u no how to anyways then plz tell me
11-17-2003, 07:59 AM
#4
2000 Watt CAFz'r
Join Date: Jan 2001
Posts: 2,026
Use proper grammar, spelling and diction and people might be more inclined to help you. I find posts that are written like your too cumbersome to read, and often don't care to finish them.
What is your current situation?
Do you have an amp?
Do you have a box?
Does your box have speaker terminals?
1st you need a box:
* Built out of 3/4 mdf minimum.
* All of the joints glued and sealed
* Big enough for your speakers
* Not too big for your speakers
* If ported tuned to a resonable frequency
2nd Install the speakers:
* If the box is not carpeted, place a gasket between the speaker and the box.
* If using a speaker terminal connect the red/positive terminal to wire and the other end of the wire to the red dot/positive terminal on the speaker.
* Do the same with the negative terminals.
* If using multiple subs figure out how you are going to wire them:
a. will they be bridged?
b. will the be wired in series or parallel?
c. what is the desired final load?
3. Installing connecting the amp.
* Connect negative power terminal to wire and wire to chassis (paint MUST be removed at contact point)
* Connect Remote wire from HU to Remote wire of amp.
* Connect sound source (depending on high-level or low-level inputs)
* Connect positive power wire to amp to fuse holder (keep the fuse out) from fue holder then to the battery.
* Wire the speakers according to the pattern you have chosen.
When everything is connected, then install the fuse.
You see, there are way too many variables right now. As Fatwhacker said, give us some more information and we will be glad to help (and clean up your English and we will be glad to help)
What is your current situation?
Do you have an amp?
Do you have a box?
Does your box have speaker terminals?
1st you need a box:
* Built out of 3/4 mdf minimum.
* All of the joints glued and sealed
* Big enough for your speakers
* Not too big for your speakers
* If ported tuned to a resonable frequency
2nd Install the speakers:
* If the box is not carpeted, place a gasket between the speaker and the box.
* If using a speaker terminal connect the red/positive terminal to wire and the other end of the wire to the red dot/positive terminal on the speaker.
* Do the same with the negative terminals.
* If using multiple subs figure out how you are going to wire them:
a. will they be bridged?
b. will the be wired in series or parallel?
c. what is the desired final load?
3. Installing connecting the amp.
* Connect negative power terminal to wire and wire to chassis (paint MUST be removed at contact point)
* Connect Remote wire from HU to Remote wire of amp.
* Connect sound source (depending on high-level or low-level inputs)
* Connect positive power wire to amp to fuse holder (keep the fuse out) from fue holder then to the battery.
* Wire the speakers according to the pattern you have chosen.
When everything is connected, then install the fuse.
You see, there are way too many variables right now. As Fatwhacker said, give us some more information and we will be glad to help (and clean up your English and we will be glad to help)
11-17-2003, 05:53 PM
#5
1000 Watt CAFz'r
Join Date: Oct 2003
Posts: 1,649
11-20-2003, 06:36 PM
#7
50 Watt CAFz'r
Join Date: Nov 2003
Posts: 278
Thread
Thread Starter
Forum
Replies
Last Post
Scottie
General Discussion
2
01-07-2011 06:23 PM
efxtruck
Canadian General Car Audio Discussion
33
08-16-2009 12:43 AM
Father Yuli
General Discussion
7
11-09-2003 03:10 PM
