Need help 2 15in powerbass m-15 ported sub enclosure
Need help 2 15in powerbass m-15 ported sub enclosure
Vehicle : 2003 Kia Rio
Location in the vehicle: Trunk
Space available (Length x Width x Height): 36x36x15
Subwoofer make and model: Powerbass m-15
Subwoofer Size: 15in
Number of Subwoofers: 2
What type of music do you like?: Rock
Is your goal SPL or Everyday Music?: everyday music
Tuning Freq (Hz): 35 Hz
Closest specs I could find to my speaker
Gross Vb Internal 5.0 cu.ft
Circular Port 5” x 4.35” D
Fb (Box Tuning) 35Hz
F3 (-3dB Cutoff) 29Hz
Pe (Watts-Rms) 150-425
Subsonic Filter Setting If Applicable 30Hz
I put these specs into www.bcae1.com/spboxnew2
I found my trunk has a gross volume of 9 cubic feet which is one foot less then the recommended build. I need help with the box design if its fine going one foot under recommended if not i need new ideas. Any help would be greatly appreciated.
Location in the vehicle: Trunk
Space available (Length x Width x Height): 36x36x15
Subwoofer make and model: Powerbass m-15
Subwoofer Size: 15in
Number of Subwoofers: 2
What type of music do you like?: Rock
Is your goal SPL or Everyday Music?: everyday music
Tuning Freq (Hz): 35 Hz
Closest specs I could find to my speaker
Gross Vb Internal 5.0 cu.ft
Circular Port 5” x 4.35” D
Fb (Box Tuning) 35Hz
F3 (-3dB Cutoff) 29Hz
Pe (Watts-Rms) 150-425
Subsonic Filter Setting If Applicable 30Hz
I put these specs into www.bcae1.com/spboxnew2
I found my trunk has a gross volume of 9 cubic feet which is one foot less then the recommended build. I need help with the box design if its fine going one foot under recommended if not i need new ideas. Any help would be greatly appreciated.
Can I get your opinion on the matter would it be better to build a box for one sub to specs or build a box for both the subs but cut off some cubic feet. I don't know much about building boxes so some help designing one would be greatly appreciated. I'm actually new to car audio altogether and trying to make do with what I have.
I don't beleive the specs powerbass puts out, so my advice is to use 3.5 net for each sub which is about typical for a 15, so you total volume after all displacement (Vb) would be 7 cuft.
I am a bit busy atm, but if you can wait, I can help you with a design.
I am a bit busy atm, but if you can wait, I can help you with a design.
Ok no problem.
How would you like the sub and port orientation?
From your max dimension, the sub cannot go in front because of the height which is 15"
You are probably looking at sub on top, port in the front, or sub on top, port at the back, I recommend the first.
It's a trunk car right?
Do your seats fold down?
Can you fit the box in through the back seat?, if not you would have to either do one 15, or build the box inside the trunk?
How would you like the sub and port orientation?
From your max dimension, the sub cannot go in front because of the height which is 15"
You are probably looking at sub on top, port in the front, or sub on top, port at the back, I recommend the first.
It's a trunk car right?
Do your seats fold down?
Can you fit the box in through the back seat?, if not you would have to either do one 15, or build the box inside the trunk?
Last edited by Sonic; Dec 12, 2012 at 09:17 PM.
Thread
Thread Starter
Forum
Replies
Last Post
wasted911
General Discussion
7
May 4, 2017 08:40 PM
HyundaiGuyMTX
Enclosure Design & Construction Help
1
Jun 25, 2006 03:10 PM



