hey everyone, got a question on the t3-1000d i just picked up
50 Watt CAFz'r
Joined: Sep 2006
Posts: 477
Straight off the ultimate website. Ultimate Sound
Continuous Bridged Power: 1000w x 1 @ 4 ohms
1200w x 1 @ 2 ohms
Maximum Bridged Power: 1600w x 1 @ 4 ohms
3500w x 1 @ 2 ohms
Frequency Response: 20 - 200 Hz
THD: 0.04%
Signal to Noise Ratio: 91db
Remote Volume Control Option: Yes
Damping Factor: 220 @ 4 ohms
Dimensions: 28cm x 58cm x 6cm
Technical Brief: PDF: 178Kb
Oddly enough, in the technical manual, it does refer to have a mono and stereo mode. Now I'm going to have to buy one to play with...
Continuous Bridged Power: 1000w x 1 @ 4 ohms
1200w x 1 @ 2 ohms
Maximum Bridged Power: 1600w x 1 @ 4 ohms
3500w x 1 @ 2 ohms
Frequency Response: 20 - 200 Hz
THD: 0.04%
Signal to Noise Ratio: 91db
Remote Volume Control Option: Yes
Damping Factor: 220 @ 4 ohms
Dimensions: 28cm x 58cm x 6cm
Technical Brief: PDF: 178Kb
Oddly enough, in the technical manual, it does refer to have a mono and stereo mode. Now I'm going to have to buy one to play with...
Last edited by Smoke_31; Apr 28, 2007 at 08:22 AM.
Thread Starter
0 Watt CAFz'r
Joined: Apr 2007
Posts: 13
hey smartass, thanks again for your advise.
just finished looking on another board i'm on and someone there benchtested these amps. here is the link:
http://www.caraudio.com/forum/showthread.php?t=225080&page=4
just finished looking on another board i'm on and someone there benchtested these amps. here is the link:
http://www.caraudio.com/forum/showthread.php?t=225080&page=4
Last edited by flaboyz/28; Apr 28, 2007 at 03:33 PM.
Originally Posted by Haunz
^ I dunno.... I think you've delt with these amps but what I saw online was:
Output Power at 13.8V:
2 x 530W @ 4 ohms stereo (65A)
1 x 1800W @ 4 ohms mono (105A)
2 x 800W @ 2 ohms stereo (98A)
1 x 2700W @ 2 ohms mono (210A)
Ratings don't neassarilly make much sense to me but from the pic of the amp posted you can see how the channels bridge up......... no way thats internal if the pic is accurate........ the bridged connection is in series between hot terminals!
Output Power at 13.8V:
2 x 530W @ 4 ohms stereo (65A)
1 x 1800W @ 4 ohms mono (105A)
2 x 800W @ 2 ohms stereo (98A)
1 x 2700W @ 2 ohms mono (210A)
Ratings don't neassarilly make much sense to me but from the pic of the amp posted you can see how the channels bridge up......... no way thats internal if the pic is accurate........ the bridged connection is in series between hot terminals!
Thread Starter
0 Watt CAFz'r
Joined: Apr 2007
Posts: 13
thanks trojan, i'm pretty pleased with it. first time i have done this from start to finish without help, and first time i have done a visible system where i had to be neat. also first ampboard for me too. sure it could have been better but i think it looks pretty good.
