Do anyone know where I could find tech support for the Clifford G4 series security/remote start?

Having some issues getting the Intellistart-4 to work with the Concept 600, all I'm getting is 4 flash from the parks and no crank.

 

You mean IG6000 right?



what's the year/make/model of your vehicle, is it auto or standard?

 

Its an auto 92 Accord.... a very straight forward install. the security system is a G-4 Concept 600.

I'm just not too familar with the Clifford Intellistart-4 remote start. I have checked all the wires like for auto a blk/grn to be grounded and e-brake/reverse light wire and tech wires etc.

The Intellistart-4 just don't seems to response... no relay clicks nothing just four flash from the parks.

 

Wiring Description for the 12-Pin Connector
Pin Col our Con nects to
1 Red/White Headlight input (+) or (-)
2 White/Orange Window switch 2 input
3 Violet Window motor 1 output
4 White/Violet Window switch 1input
5 Red Window supply input (+)12V
6 White/Green Key side starter (+) 12V
7 Red/Black Headlight output (+) or (-)
8 Green/Blue Coil side ignition (+)
9 Orange Window motor 2 output
10 White/Blue Starter side starter (+) output
11 White/Brown Key side ignition input (+)
12 Brown Parking light output (+) 12V
Wiring Description for the 14-Pin Connector
Pin Col our Con nects to
2 Blue/White Brake input/output (+) 12V
5 Blue Windshield wiper input (+)
6 White/Orange Door unlock common
7 White/Green Door lock common
8 Red/White Parking and brake light input (+) 12V
9 Brown/Red Interior light supply (+) or (-)
10 Gray Door trigger input (+) or (-)
11 Red/Orange Door unlock normally open
12 Red/Green Door lock normally open
13 Gray/Green Door lock normally closed
14 Gray/Orange Door unlock normally closed
Wiring Description for the 24-Pin Connector
Pin Col our Connects to
2 Red/Black Optional Digital OmniSensor input (5V+)
3 White/Blue Prewired Digital Proximity Sensor input connector
4 Violet LED Output (+) 12V
5 Black/Gray Ignition coil or tach input
6 Red Proximity Sensor and Tilt Sensor power supply (+) 12V
7 Blue/Yellow Windshield wiper input (-)
8 Gray/Yellow Trunk trigger switch input (-)
9 Black Sensors, LED and valet switch ground supply (-)
10 Black Ground
11 White Valet Switch input (-) multi-plex
12 Gray twinlead Light sensor input (NightVision)
13 Gray/Violet Auxilliary Output A output
14 Gray/Blue Auxilliary Output B output
15 Gray/Red Auxilliary Output C output
17 Yellow Optional airhorns or siren output (-)
18 Red Battery input (+) 12V
19 Black twinlead Not used
20 Green Tilt Sensor armed output
21 Black twinlead Not used
22 Gray twinlead Light sensor input (NightVision)
23 White/Black Hood trigger switch input (-)
24 Orange Tilt Sensor input (-)

Also check to endure that the Ant is pluged in correctly

 

ok, you have tach programmed?

there really isn't anything as far as descriptions for parklight flashes, but I know when it's working properly, the lights flash twice then it starts.

I have the same setup in my car, and have never had a problem.

 

Claudio Piccolo

thanks for the wiring code.... I'll check it against mine.

The Concept 600 do works, just the remote start not responding to the #4 button or * button.


Extreme1

How do you program the tach input? I have the tach wire (blk/grey wire) hook up to the coil. I also tried with it off, but still nothing.

 

it won't work without tach.

Mandatory RPM Programming
Note: This MAN DA TORY pro gram ming step must be com pleted for the In tel liS tart 4 to op er ate prop erly.
1. Drive the vehicle to a nearby open area and allow the engine to warm-up until the RPMs drop to the normal idle speed.
2. With the engine still running, place the transmission in PARK (or NEUTRAL if the vehicle has a manual transmission).
3. Enter installer-programming mode following the instruction provided in the Programmable Features section of the alarm.
4. Press the unmarked button of the PlainView 2 Switch once. After a three-second pause, the system will sound one chirp to
confirm column one selection (see the Installer-Programmable Features section of the system to which you are adding IntelliStart 4).
5. Press the Q button of the PlainView 2 Switch five times (you will hear a chirp each time you press the button) to select row five.
After a two-second pause, you will hear two chirps and two parking light flashes to confirm idle RPM has been set (if you hear just
one chirp, check the connection of the BLACK/GRAY wire, then repeats steps 1 - 5).
6. Turn the ignition OFF.

 

^ thanks for the info.

I definately didn't do the tach programming procedure..... I'll give that a try later and report back. thx

 

Interesting........... Extreme1 deleted all his post!

Anyways, tried it today and still the same... no crank. and thats after it has comfirmed the tach is programmed.. with 2 chirp.

Any other suggestions?

 

No I didn't, I got banned, someone else deleted all my posts.


go to directed's website and there should be a tech link or phone # there.