hey everyone, got a question on the t3-1000d i just picked up

Reply Subscribe

Thread Tools

Search this Thread

04-28-2007, 08:19 AM

#11

Smoke_31

50 Watt CAFz'r

Join Date: Sep 2006

Posts: 478

Straight off the ultimate website. Ultimate Sound

Continuous Bridged Power: 1000w x 1 @ 4 ohms
1200w x 1 @ 2 ohms
Maximum Bridged Power: 1600w x 1 @ 4 ohms
3500w x 1 @ 2 ohms
Frequency Response: 20 - 200 Hz
THD: 0.04%
Signal to Noise Ratio: 91db
Remote Volume Control Option: Yes
Damping Factor: 220 @ 4 ohms
Dimensions: 28cm x 58cm x 6cm
Technical Brief: PDF: 178Kb

Oddly enough, in the technical manual, it does refer to have a mono and stereo mode. Now I'm going to have to buy one to play with...

Last edited by Smoke_31; 04-28-2007 at 08:22 AM.

04-28-2007, 09:16 AM

#12

Brad-S.A.

2000 Watt CAFz'r

iTrader: (35)

Join Date: Jan 2005

Posts: 2,195

Quote:

Originally Posted by Wagoneyezed

wont smoke it will just go into protection.

For the most part it will go in to protect but I have seen a couple smoke.

04-28-2007, 03:22 PM

#13

flaboyz/28

0 Watt CAFz'r

Thread Starter

Join Date: Apr 2007

Posts: 13

hey smartass, thanks again for your advise.
just finished looking on another board i'm on and someone there benchtested these amps. here is the link:

http://www.caraudio.com/forum/showthread.php?t=225080&page=4

Last edited by flaboyz/28; 04-28-2007 at 03:33 PM.

04-28-2007, 03:40 PM

#14

Trojan

50 Watt CAFz'r

iTrader: (2)

Join Date: Feb 2006

Posts: 233

Quote:

Originally Posted by Haunz

^ I dunno.... I think you've delt with these amps but what I saw online was:

Output Power at 13.8V:
2 x 530W @ 4 ohms stereo (65A)
1 x 1800W @ 4 ohms mono (105A)
2 x 800W @ 2 ohms stereo (98A)
1 x 2700W @ 2 ohms mono (210A)

Ratings don't neassarilly make much sense to me but from the pic of the amp posted you can see how the channels bridge up......... no way thats internal if the pic is accurate........ the bridged connection is in series between hot terminals!

My numbers are much more realistic. The T3-1000 is two 500's in one case but when run bridged they see equal impedance to what you are running not half.

04-28-2007, 03:42 PM

#15

flaboyz/28

0 Watt CAFz'r

Thread Starter

Join Date: Apr 2007

Posts: 13

trojan where are your numbers? or is that you from caraudio.com?

04-28-2007, 03:55 PM

#16

Trojan

50 Watt CAFz'r

iTrader: (2)

Join Date: Feb 2006

Posts: 233

Quote:

Originally Posted by flaboyz/28

trojan where are your numbers? or is that you from caraudio.com?

One in the same!

04-30-2007, 11:49 AM

#17

flaboyz/28

0 Watt CAFz'r

Thread Starter

Join Date: Apr 2007

Posts: 13

just figured i would show the progress. this amp is rough!!!! gain is backwards on this one too, read that someone else had this problem but not a big deal to me.

04-30-2007, 11:53 AM

#18

Trojan

50 Watt CAFz'r

iTrader: (2)

Join Date: Feb 2006

Posts: 233

Looks good.

04-30-2007, 11:55 AM

#19

flaboyz/28

0 Watt CAFz'r

Thread Starter

Join Date: Apr 2007

Posts: 13

thanks trojan, i'm pretty pleased with it. first time i have done this from start to finish without help, and first time i have done a visible system where i had to be neat. also first ampboard for me too. sure it could have been better but i think it looks pretty good.