New Car, Need some Advice!! (OEM integration)
#1
New Car, Need some Advice!! (OEM integration)
Hey all, long time member, but havent been too active lately.
However, Im back, and looking for some advice on a new car I just purchased. It is a 2011 Hyundai Sonata GLS. The car has the base level stereo (sounds avg at best)
Now, previously I have always gone the standard aftermarket deck/amps/components. Ive had some decent systems, but this time around I want to keep the stock deck, for security/bluetooth/look.....
Im aware the deck isnt of overly high quality in terms of SQ, but I want to make a good attempt at some OEM integration. Im in Saskatoon, and Im forced to park close to some rougher areas, so an aftermarket double DIN is asking for trouble (ive already had previous systems hacked into, even with the faceplate removed)
So, I seek advice on my best option. Here is what I have.....
- Alpine PDX 5 amp
- MB Quart 6.5" components
- Kenwood Excelon 12" sub in custom built ported box
So now I need to tap into the factory unit. Im pretty sure there is bass roll-off when the volume is turned up on the deck, so that tells me right off the hop there is some EQ'ing going on. Im not sure of the details, but Ive tested, and compared notes with others.
Ive researched some OEM units. RE-Q, JL Cleansweep, 3sixty, Audiocontrol..... Truthfully, the 3sixty is a little too expensive and has more then I really need. The Cleansweep sounds like it might do a solid job, but Im not sure about the RE-Q. The Cleansweep does some active EQ'ing to balance out the signal. The re-Q does, but here's the issue. If the bass rolls off at high volumes, and I tweak the RE-Q for that, when the volume is lower, the bass might be way too abundant.
I dont understand how the deck changes the EQ, and if it rolls off bass for every incremental volume increase, or if say after 20, it cuts the lows by a certain amount. It would be nice to know, but tough to diagnose without some fancy testing gear.
What would be a good choice, the Cleansweep, or the RE-Q, or?
Im going to leave the rear speakers stock , and likely not even power them off the amp. HAvent decided on that..
As well, can someone recommend a good installer in Saskatoon?!? I dont have a garage or many resources to do a clean quality install, and I dont want to butcher my vehicle.
Thanks for any suggestions/advice!!!
However, Im back, and looking for some advice on a new car I just purchased. It is a 2011 Hyundai Sonata GLS. The car has the base level stereo (sounds avg at best)
Now, previously I have always gone the standard aftermarket deck/amps/components. Ive had some decent systems, but this time around I want to keep the stock deck, for security/bluetooth/look.....
Im aware the deck isnt of overly high quality in terms of SQ, but I want to make a good attempt at some OEM integration. Im in Saskatoon, and Im forced to park close to some rougher areas, so an aftermarket double DIN is asking for trouble (ive already had previous systems hacked into, even with the faceplate removed)
So, I seek advice on my best option. Here is what I have.....
- Alpine PDX 5 amp
- MB Quart 6.5" components
- Kenwood Excelon 12" sub in custom built ported box
So now I need to tap into the factory unit. Im pretty sure there is bass roll-off when the volume is turned up on the deck, so that tells me right off the hop there is some EQ'ing going on. Im not sure of the details, but Ive tested, and compared notes with others.
Ive researched some OEM units. RE-Q, JL Cleansweep, 3sixty, Audiocontrol..... Truthfully, the 3sixty is a little too expensive and has more then I really need. The Cleansweep sounds like it might do a solid job, but Im not sure about the RE-Q. The Cleansweep does some active EQ'ing to balance out the signal. The re-Q does, but here's the issue. If the bass rolls off at high volumes, and I tweak the RE-Q for that, when the volume is lower, the bass might be way too abundant.
I dont understand how the deck changes the EQ, and if it rolls off bass for every incremental volume increase, or if say after 20, it cuts the lows by a certain amount. It would be nice to know, but tough to diagnose without some fancy testing gear.
What would be a good choice, the Cleansweep, or the RE-Q, or?
Im going to leave the rear speakers stock , and likely not even power them off the amp. HAvent decided on that..
As well, can someone recommend a good installer in Saskatoon?!? I dont have a garage or many resources to do a clean quality install, and I dont want to butcher my vehicle.
Thanks for any suggestions/advice!!!
#2
Alpine makes a nice piece, PXE-H660.
I've used one in an install that i did, and was quite happy with the rests.
The re-q is a very basic piece with a bass restoration circuit built in.
Spend a little extra and get something that will give you some TA, EQ, and level control.
I've used one in an install that i did, and was quite happy with the rests.
The re-q is a very basic piece with a bass restoration circuit built in.
Spend a little extra and get something that will give you some TA, EQ, and level control.
#5
JL Audio makes Clean Sweep designed specifically for OEM integration:
http://mobile.jlaudio.com/products_c...php?page_id=94 . Hope this helps you & Good Luck!
http://mobile.jlaudio.com/products_c...php?page_id=94 . Hope this helps you & Good Luck!
Thread
Thread Starter
Forum
Replies
Last Post
scotiacustom
General Discussion
20
03-01-2007 05:17 PM