some q's any help appreciated
#1
I have some q's and any help would be appreciated. so heres what i have for the bass in my car.
Lanzar vibe 1600 watt amp
2 x 400 Watts RMS at 4 Ohms
2 x 800 Watts Max at 4 Ohms
1 x 1600 Watts Max at 4 Ohms Bridged
2 x 650 Watts at 2 Ohms
Electronic Crossover Network
Bass Boost Circuit
Bridgeable at 4 Ohms
2 Ohms Stereo Stable
Tri-Mode Capable
Gold RCA Inputs
Line Outs For Left & Right Channels.
Power & Protection LED Indicators
Advanced Protection Circuitry
Soft Turn On/Off
Remote Control Bass Booster
I know i will not get full effencicy from this amp but how how many watts do you think it will actually put out? I am thinking to run it at 4 ohms briged because i have 2 of these:
Bazooka 12" dual voice coil
RSW1224DVC
Power Handling 350w - 400w *max power wired in parallel*
Power Handling with Liquid Cooling 500w *max power wired in parallel*
Impedance Dual 4 Ohm
Sensitivity 88
Recommended Power 50w - 225w (RMS) per coil
How do you think i should wire this up? Should i go ported or sealed? i am fiberglassing these into the trunk. What guage wire do i need to run from the amp to the subs? is regular speaker wire ok?
Although the amp it 2 ohm stereo stable, would it make sense to run it in 4 ohm briged to not work it as hard. Finally do you think this will sound alright?
Lanzar vibe 1600 watt amp
2 x 400 Watts RMS at 4 Ohms
2 x 800 Watts Max at 4 Ohms
1 x 1600 Watts Max at 4 Ohms Bridged
2 x 650 Watts at 2 Ohms
Electronic Crossover Network
Bass Boost Circuit
Bridgeable at 4 Ohms
2 Ohms Stereo Stable
Tri-Mode Capable
Gold RCA Inputs
Line Outs For Left & Right Channels.
Power & Protection LED Indicators
Advanced Protection Circuitry
Soft Turn On/Off
Remote Control Bass Booster
I know i will not get full effencicy from this amp but how how many watts do you think it will actually put out? I am thinking to run it at 4 ohms briged because i have 2 of these:
Bazooka 12" dual voice coil
RSW1224DVC
Power Handling 350w - 400w *max power wired in parallel*
Power Handling with Liquid Cooling 500w *max power wired in parallel*
Impedance Dual 4 Ohm
Sensitivity 88
Recommended Power 50w - 225w (RMS) per coil
How do you think i should wire this up? Should i go ported or sealed? i am fiberglassing these into the trunk. What guage wire do i need to run from the amp to the subs? is regular speaker wire ok?
Although the amp it 2 ohm stereo stable, would it make sense to run it in 4 ohm briged to not work it as hard. Finally do you think this will sound alright?
#3
Yeah, run it 4 ohms bridged to the two subs to get the most out of your setup. With ported you'll get a louder boomier bass than with a sealed enclosure. I'm not sure if the amp has a subsonic filter - if you're going to go ported you may want to make sure the amp has one. If not you may risk damaging the sub at low frequencies.
From my amp to my subs I think I'm running 12 guage but I'm not entirely sure. It seems to work fine for me.
[ March 18, 2004, 09:32 PM: Message edited by: Muckaluck ]
From my amp to my subs I think I'm running 12 guage but I'm not entirely sure. It seems to work fine for me.
[ March 18, 2004, 09:32 PM: Message edited by: Muckaluck ]
Thread
Thread Starter
Forum
Replies
Last Post
integra96
General SPL
9
01-28-2013 12:19 AM