Can you bridge a 4 channel amp and still power a sub?
#1
Can you bridge a 4 channel amp and still power a sub?
Recently I've been mulling over alternatives for my system. I've got a PPI 4 channel amp, focal separates up front and a MMats sub, DVC @ 4 ohms per coil.
I thought I read somewhere you could bridge to 2 channels, filtering the bass and running it to the sub. Is this possible with my system?
I thought I read somewhere you could bridge to 2 channels, filtering the bass and running it to the sub. Is this possible with my system?
#3
I'm not sure if I adequately explained what I want to do. I want to run my separates AND my sub off of my amp, bridging it to 2 channels. It seems to me I would need a 3 way crossover after the amp to get it done.
If this is possible, is it superior to my present configuration ( 4 channels, 2 to front separates, 2 to the DVC sub), or is it just another way of getting to the same result.
If this is possible, is it superior to my present configuration ( 4 channels, 2 to front separates, 2 to the DVC sub), or is it just another way of getting to the same result.
#4
to make sure, you want to bridge channels 1 and 2 to power one speaker, 3 and 4 to another, and have the sub running off of both? you're better off leaving it, or buying a seperate subwoofer amp.
to properly do what you want, you need to run everything in series, cutting back on the power. therefor you would actually be getting half the power you are right now.
to properly do what you want, you need to run everything in series, cutting back on the power. therefor you would actually be getting half the power you are right now.
#5
Yes this can be done but it will necessitate you building a passive crossover network. You will also only be able to use one coil on the subwoofer. It is best to leave the amp running in 3 channel mode, channels 1&2 to the component speakers, channel 3 & 4 bridged to the sub (again only using one voice coil).
#7
I'm not sure if yor confused or me but here it goes
Your 4 chan amp is bridgeable to 3 channels
the two unbridged channels will run your main staging speakers being your Focals
Your other two channels will be bridged to one channel to run your sub at 2ohms mono this is beyond the rated load of your apm but providing you supply the amp with enough current and airflow you will not have a problem.
the main channels running the focals will be using the high pass filter and the other channels will be lowpassed
periodically depending on how hard you run the system it will thermal out but if you use cooling fans it will help
Your 4 chan amp is bridgeable to 3 channels
the two unbridged channels will run your main staging speakers being your Focals
Your other two channels will be bridged to one channel to run your sub at 2ohms mono this is beyond the rated load of your apm but providing you supply the amp with enough current and airflow you will not have a problem.
the main channels running the focals will be using the high pass filter and the other channels will be lowpassed
periodically depending on how hard you run the system it will thermal out but if you use cooling fans it will help
#8
i actualy ran a 1ohm load off my amp, bridged. (rated at 4 ohms). It went into protection as soon as I started cranking up the volume. But, it's still fine... I'm not sure if it goes into protection from heat, or if it's from too much current reaching the speaker output...
Anyways, if you're conservative on the amount of power you give your subs, you should be ok running it at 2ohms bridged.
Anyways, if you're conservative on the amount of power you give your subs, you should be ok running it at 2ohms bridged.
#9
Yeah, I think that may be a little risky for me. However, I'm presently running my 4 channel amp unbridged, with the 2 rear channels each connected to one VC of my DVC sub. It seems some are recommending bridging the rear 2 channels and running one coil. This would actually give me 300 watts instead of 75x2 at the sub, and sounds tempting, but is this acceptable for a DVC sub?
#10
are all four channels bridge-able, 4 to 2, cuz you could run your comps from each channel, and parallel to your sub, but unless your running in mono, which wouldnt optimize your comps, then you'll be running stereo to your sub, not so good. But if you use 2 svc subs then it wont be too bad at all.
Thread
Thread Starter
Forum
Replies
Last Post
d4rin
Car Audio Technical Discussions
4
11-08-2009 02:12 PM
jettalemon
General Discussion
0
06-17-2007 08:26 AM