Help with Amplifier/sub and WRMS and OHMS
#1
Specs:
* High Quality MDF Construction
* Spun Aluminum Venturi Ports
* Durable Gray Carpeting
* 3/8" Plexiglass Window
* Blue Interior Neon Lighting
* Mirrored Interior Panels
* Extended & Vented Pole Piece
* Gold Binding Post Terminals
* DUAL ANGLE 12 TUNED
BANDPASS SYSTEM
* High Quality MDF Construction
* Black Suppleather Covering
* 3/8" Plexiglass Window
* Blue Interior Neon Lighting
* Mirrored Interior Panels
* Dual 12" PHAT 2" Foam Surround,
* Non-Pressed KM3(tm) Coated
* Cone Subwoofers
* 50 oz. Strontium Magnet
* 2" 4 Layer ASV Voice Coil
* Bumped Back Plate
* Extended & Vented Pole Piece
* Gold Binding Post Terminals
* Power Handling: 800 Watts RMS
* Sensitivity: 104dB
* Frequency Response: 28Hz - 150Hz
* Impedance: 4 Ohm Stereo
* Dimensions:
15(H) x 29.75(W) x 16.75(D)
Here is the 3d view.
The subs are definitively SVC
http://www.circuitcity.com/modeldisplay.jsp?c=1&ModelID=/IMAGE/nueweb/adb/NW.ADB.ABP122T.SWF&OID=77173&CMPageID=3D%20View:%2 0ADB%20ABP122T%20Audiobahn%20Dual%2012%22%20Subwoo fer%20 Bandpass%20System&CMCategoryID=3D%20VIEW%20%3E%20C AR%20%3E%20SUBWOOFERS]http://www.circuitcity.com/modeldisplay.jsp?c=1&ModelID=/IMAGE/nueweb/adb/NW.ADB.ABP122T.SWF&OID=77173&CMPag eID=3D%20View:%20ADB%20ABP122T%20Audiobahn%20Dual% 2012%22%20Subwoofer%20Bandpass%20System&CMCategory ID=3D%20VIEW%20%3E%20CAR%20%3E%20SUBWOOFERS[/url]
And I have this amplifier
specs:
* Brand New Audiobahn A8002T 2 Channel 1600W Amp
* Class A/B MOSFET Power Amplifier
* 2 Ohm Stereo Stable
* MOSFET High Speed Switching Power Supply
* Non-Regulated Power Supply
* Double Sided Epoxy Circuit Board
* Air Induction Fan Cooled
* RCA (Low Level) Inputs
* Speaker (Hight Level) Inputs
* RCA Outputs
* Variable High Pass Crossover : 50Hz - 750Hz
* Variable Low Pass Crossover : 50Hz - 120Hz
* Variable Subsonic Filter : 20Hz - 50Hz
* 12dB Crossover Slope
* Signal to Noise Ratio >100dB
* 0.02% T.H.D.
* 18dB Bass Boost
* Bass Boost Control On/Off
* Phase Shift 0° - 180°
* 1/2/3 Channel Operation (Mixed Mono)
* Tri-way capable
* Soft Start Circuitry
* High Gloss Chrome Plate Finish
* Blue Illumination
* 4-Way Protection Circuitry: Thermal, Short Circuit, Overload, DC Offset
* 30A x 2 Fuses
* Dimensions: 11-1/16"W x 1-7/8"H x 11-7/8"D
* 2 x 200W RMS @ 4 Ohm
* 2 x 400W RMS @ 2 Ohm
* 1 x 800W RMS @ 4 Ohm
Most people said this subs don't fit with this amplifier, cause I can reach 200 WRMS max if I plug each sub in each channel.
But the Audiobahn site say ABP122T and A8002T correctly fit in this official site.
http://www.audiobahn.com/tech/Inform...Enclosures.pdf
How Can I wire this stuff to get the maximum for these subs? Parallel... serie??
Thanx to help me... and sorry about my bad english [img]tongue.gif[/img]
Thread
Thread Starter
Forum
Replies
Last Post
voided
Car Audio Wanted (WTB)
0
05-29-2007 11:46 PM