BEST AMPS FOR STREET!!
Originally posted by MTA:
hmmmm just played around with the American Bass 200.1 at 0.25 ohm
result is not too bad at all 38volts and 69.6amps\totaling 2644.8 watts RMS...this test was done on a single semi charged Optima Yellow top 31 series with 2 RE10SX's dual 1 ohm coils
hmmmm just played around with the American Bass 200.1 at 0.25 ohm
result is not too bad at all 38volts and 69.6amps\totaling 2644.8 watts RMS...this test was done on a single semi charged Optima Yellow top 31 series with 2 RE10SX's dual 1 ohm coils
148.7 but cut out too soon and went into protection..I know if it didnt shut down it will hit a 150 easily...from volume 59 it does 146.8-147.0 to vol 60 does 147.8-148 1-2 seconds into vol 61 hits 148.7 and goes into protect...if I could keep it out of protection it would be insanely loud [img]smile.gif[/img]
mind you I was kinda surprised with the results... I have a feeling Im overloading the power supply... nice current but the voltage is too low... I would like to see lower current and a bit higher voltage... wish I could test it at 0.35 in this application...it did quite a bit more power at 0.5ohms the voltage was in the 50's and current was still above 60amps... I have a feeling he amp might be current protected at 70amps??? anyone know this? becasue each test i did always shut down just as the current meter got right close to it
[ April 09, 2005, 09:39 PM: Message edited by: MTA ]
[ April 09, 2005, 09:39 PM: Message edited by: MTA ]
america bass 200.1 version of this specific 3000d board will not play well at 0.25 ohm
(other versions of this board are in the spl dynamics, e audio and ground zero amps)
here is a hint for u to try to work it at 0.25 ohm........u know how this version has the remote bass control, get the actual **** with the wire and play with that in your testings at 0.25 ohm.........u just might have luck.
(other versions of this board are in the spl dynamics, e audio and ground zero amps)
here is a hint for u to try to work it at 0.25 ohm........u know how this version has the remote bass control, get the actual **** with the wire and play with that in your testings at 0.25 ohm.........u just might have luck.
Guest
Posts: n/a
Peter that is funny why your vol is so low in your test. From what i have heard from some people they where getting over 8k strapped from a pair 150.1 and the 200.1 are 25% more output so do the math. Rf guys where getting 159v out off 2 bd1500 and the 150.1 walk all over them if im not mistaken i heard 200v out of a pair strapped which i can belive cause i used to get 137v&39amps out of a 2000x at 2ohms.P.s if you can fin an old zr1000 we got over 120v out of that amp back in the day also.
Originally posted by Mr.American Bass:
Peter that is funny why your vol is so low in your test. From what i have heard from some people they where getting over 8k strapped from a pair 150.1 and the 200.1 are 25% more output so do the math. Rf guys where getting 159v out off 2 bd1500 and the 150.1 walk all over them if im not mistaken i heard 200v out of a pair strapped which i can belive cause i used to get 137v&39amps out of a 2000x at 2ohms.P.s if you can fin an old zr1000 we got over 120v out of that amp back in the day also.
Peter that is funny why your vol is so low in your test. From what i have heard from some people they where getting over 8k strapped from a pair 150.1 and the 200.1 are 25% more output so do the math. Rf guys where getting 159v out off 2 bd1500 and the 150.1 walk all over them if im not mistaken i heard 200v out of a pair strapped which i can belive cause i used to get 137v&39amps out of a 2000x at 2ohms.P.s if you can fin an old zr1000 we got over 120v out of that amp back in the day also.
[ April 10, 2005, 05:36 PM: Message edited by: MTA ]
Originally posted by Prolifik:
america bass 200.1 version of this specific 3000d board will not play well at 0.25 ohm
(other versions of this board are in the spl dynamics, e audio and ground zero amps)
here is a hint for u to try to work it at 0.25 ohm........u know how this version has the remote bass control, get the actual **** with the wire and play with that in your testings at 0.25 ohm.........u just might have luck.
america bass 200.1 version of this specific 3000d board will not play well at 0.25 ohm
(other versions of this board are in the spl dynamics, e audio and ground zero amps)
here is a hint for u to try to work it at 0.25 ohm........u know how this version has the remote bass control, get the actual **** with the wire and play with that in your testings at 0.25 ohm.........u just might have luck.
